Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
Have you been looking for help on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a reasonably tough task. If the old tub is conveniently easily accessible, the project can relocate immediately; if you need to open a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually certified yourself for the task and also fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to think about using one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will help you mount a brand-new bath tub in your bathroom if you have actually already acquired a new tub and don't need to alter the plan of your previous water system pipes.
Your tools as well as product list need to comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the water system. After doing so, activate the taps to drain any water staying in the system. The procedure of removing the existing taps can be quite bothersome due to the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipelines. When the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines are in place between the faucet and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the tub up until the level checks out degree.
To set up taps, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water system as well as check all joints as well as new pipework for leakages as well as tighten them if essential. Fill the bath tub and additionally examine the overflow outlet as well as the typical outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of once as this will certainly resolve it right into its last position.
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bath needs to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid strain on the tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall between the bath and also the tiling, bring about complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather very early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that post on How to Install a Bathtub Yourself when surfing around the web. Sharing is caring. Helping others is fun. Thank you for your time. Visit again soon.
Book My Estimate Report this page